Activated Graphene Oxide-Calcium Alginate Beads for Adsorption of Methylene Blue and Pharmaceuticals.

The remarkable adsorption capacity of graphene-derived materials has prompted their examination in composite materials suitable for deployment in treatment of contaminated waters. In this study, crosslinked calcium alginate-graphene oxide beads were prepared and activated by exposure to pH 4 by using 0.1M HCl. The activated beads were investigated as novel adsorbents for the removal of organic pollutants (methylene blue dye and the pharmaceuticals famotidine and diclofenac) with a range of physicochemical properties. The effects of initial pollutant concentration, temperature, pH, and adsorbent dose were investigated, and kinetic models were examined for fit to the data. The maximum adsorption capacities qmax obtained were 1334, 35.50 and 36.35 mg g-1 for the uptake of methylene blue, famotidine and diclofenac, respectively. The equilibrium adsorption had an alignment with Langmuir isotherms, while the kinetics were most accurately modelled using pseudo- first-order and second order models according to the regression analysis. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated and the adsorption process was determined to be exothermic and spontaneous.

Pilot Scale Study: First Demonstration of Hydrophobic Membranes for the Removal of Ammonia Molecules from Rendering Condensate Wastewater.

Hydrophobic membrane contactors represent a promising solution to the problem of recycling ammoniacal nitrogen (N-NH4) molecules from waste, water or wastewater resources. The process has been shown to work best with wastewater streams that present high N-NH4 concentrations, low buffering capacities and low total suspended solids. The removal of N-NH4 from rendering condensate, produced during heat treatment of waste animal tissue, was assessed in this research using a hydrophobic membrane contactor. This study investigates how the molecular composition of rendering condensate wastewater undergo changes in its chemistry in order to achieve suitability to be treated using hydrophobic membranes and form a suitable product. The main objective was to test the ammonia stripping technology using two types of hydrophobic membrane materials, polypropylene (PP) and polytetrafluoroethylene (PTFE) at pilot scale and carry out: (i) Process modification for NH3 molecule removal and (ii) product characterization from the process. The results demonstrate that PP membranes are not compatible with the condensate waste as it caused wetting. The PTFE membranes showed potential and had a longer lifetime than the PP membranes and removed up to 64% of NH3 molecules from the condensate waste. The product formed contained a 30% concentrated ammonium sulphate salt which has a potential application as a fertilizer. This is the first demonstration of hydrophobic membrane contactors for treatment of condensate wastewater.

Development of a selective inhibitor for Kv1.1 channels prevalent in demyelinated nerves.

Members of the voltage-gated K+ channel subfamily (Kv1), involved in regulating transmission between neurons or to muscles, are associated with human diseases and, thus, putative targets for neurotherapeutics. This applies especially to those containing Kv1.1 α subunits which become prevalent in murine demyelinated axons and appear abnormally at inter-nodes, underlying the perturbed propagation of nerve signals. To overcome this dysfunction, akin to the consequential debilitation in multiple sclerosis (MS), small inhibitors were sought that are selective for the culpable hyper-polarising K+ currents. Herein, we report a new semi-podand - compound 3 - that was designed based on the modelling of its interactions with the extracellular pore region in a deduced Kv1.1 channel structure. After synthesis, purification, and structural characterisation, compound 3 was found to potently (IC50 = 8 µM) and selectively block Kv1.1 and 1.6 channels. The tested compound showed no apparent effect on native Nav and Cav channels expressed in F-11 cells. Compound 3 also extensively and selectively inhibited MS-related Kv1.1 homomer but not the brain native Kv1.1- or 1.6-containing channels. These collective findings highlight the therapeutic potential of compound 3 to block currents mediated by Kv1.1 channels enriched in demyelinated central neurons.

A Rational Design of a Selective Inhibitor for Kv1.1 Channels Prevalent in Demyelinated Nerves That Improves Their Impaired Axonal Conduction.

K+ channels containing Kv1.1 α subunits, which become prevalent at internodes in demyelinated axons, may underlie their dysfunctional conduction akin to muscle weakness in multiple sclerosis. Small inhibitors were sought with selectivity for the culpable hyper-polarizing K+ currents. Modeling of interactions with the extracellular pore in a Kv1.1-deduced structure identified diaryldi(2-pyrrolyl)methane as a suitable scaffold with optimized alkyl ammonium side chains. The resultant synthesized candidate [2,2'-((5,5'(di-p-topyldiaryldi(2-pyrrolyl)methane)bis(2,2'carbonyl)bis(azanediyl)) diethaneamine·2HCl] (8) selectively blocked Kv1.1 channels (IC50 ≈ 15 µM) recombinantly expressed in mammalian cells, induced a positive shift in the voltage dependency of K+ current activation, and slowed its kinetics. It preferentially inhibited channels containing two or more Kv1.1 subunits regardless of their positioning in concatenated tetramers. In slices of corpus callosum from mice subjected to a demyelination protocol, this novel inhibitor improved neuronal conduction, highlighting its potential for alleviating symptoms in multiple sclerosis.

UV-induced photocatalytic degradation of aqueous acetaminophen: the role of adsorption and reaction kinetics.

Nanostructured titania supported on activated carbon (AC), termed as integrated photocatalytic adsorbents (IPCAs), were prepared by ultrasonication and investigated for the photocatalytic degradation of acetaminophen (AMP), a common analgesic and antipyretic drug. The IPCAs showed high affinity towards AMP (in dark adsorption studies), with the amount adsorbed proportional to the TiO2 content; the highest adsorption was at 10 wt% TiO2. Equilibrium isotherm studies showed that the adsorption followed the Langmuir model, indicating the dependence of the reaction on an initial adsorption step, with maximum adsorption capacity of 28.4 mg/g for 10 % TiO2 IPCA. The effects of initial pH, catalyst amount and initial AMP concentration on the photocatalytic degradation rates were studied. Generally, the AMP photodegradation activity of the IPCAs was better than that of bare TiO2. Kinetic studies on the photocatalytic degradation of AMP under UV suggest that the degradation followed Langmuir-Hinshelwood (L-H) kinetics, with an adsorption rate constant (K) that was considerably higher than the photocatalytic rate constant (k r), indicating that the photocatalysis of AMP is the rate-determining step during the adsorption/photocatalysis process.

An SPE LC-MS/MS method for the analysis of human and veterinary chemical markers within surface waters: an environmental forensics application.

In this study, the use of co-occurring discriminators of sewage and manure was assessed as a potential way to disentangle sewage and manure sources. A suite of human and veterinary derived chemical markers, which includes pharmaceuticals and compound such as food additives, has been identified for this purpose. The suite was selected in such a manner as to provide additional source characterisation, e.g. differentiating raw versus treated sewage inputs. An SPE-LC-MS/MS method was developed and validated for the determined suite of chemical markers with a detection limit of up to 50 pg L(-1). This represents one of the lowest limits of detection for pharmaceuticals reported in literature. To illustrate the suitability of the proposed method to differentiate sewage and manure inputs to surface water bodies, results from surface water samples collected at monitoring sites corresponding to specific land use types within Ireland are discussed.

Parallel microflow photochemistry: process optimization, scale-up, and library synthesis.

A novel, multimicrocapillary flow reactor (MµCFR) was constructed and applied to a series of sensitized photoadditions involving 2(5H)-furanones. The reactor allowed for rapid and energy-, time-, and space-efficient sensitizer screening, process optimization, validation, scale-up, and library synthesis.

Microphotochemistry: 4,4'-Dimethoxybenzophenone mediated photodecarboxylation reactions involving phthalimides.

A series of 4,4'-dimethoxybenzophenone mediated intra- and intermolecular photodecarboxylation reactions involving phthalimides have been examined under microflow conditions. Conversion rates, isolated yields and chemoselectivities were compared to analogous reactions in a batch photoreactor. In all cases investigated, the microreactions gave superior results thus proving the superiority of microphotochemistry over conventional technologies.

On the adsorption/photodegradation of amoxicillin in aqueous solutions by an integrated photocatalytic adsorbent (IPCA): experimental studies and kinetics analysis.

Activated carbon-supported TiO(2) nanoparticles, termed integrated photocatalytic adsorbents (IPCAs), were prepared using an ultrasonic impregnation technique and investigated for the photocatalytic degradation of amoxicillin (AMO), a ß-lactam antibiotic. The IPCAs had high adsorption affinity for AMO with the amount adsorbed proportional to the TiO(2) loading and the highest adsorption was at 10 wt% TiO(2) loading. A pseudo-second-order model was found to fit the experimental data and consistently predicted the amount of AMO adsorbed over the adsorption period. Equilibrium isotherm studies showed that the adsorption followed the Redlich-Peterson model with maximum adsorption capacity of 441.3 mg g(-1) for 10% IPCA, 23% higher than the pure activated carbon (AC). Kinetic studies on the photocatalytic degradation of AMO using non-linear regression analysis suggest that the degradation followed Langmuir-Hinshelwood (L-H) kinetics. The adsorption rate constant (K(ad)) was considerably higher than the photocatalytic rate constant (k(L-H)), indicating that the photocatalysis of AMO is the rate-determining step during the adsorption/photocatalysis process. The 10% IPCA exhibited excellent stability and reusability over four photodegradation cycles.

Microphotochemistry: a reactor comparison study using the photosensitized addition of isopropanol to furanones as a model reaction.

Three types of micro-photoreactor setups were investigated using DMBP-sensitized additions of isopropanol to furanones as model reactions. The results were compared to experiments using a conventional batch reactor. Based on conversion rates, reactor geometries and energy efficiency calculations the microsystems showed superior performances over the batch process. Of the three micro setups examined, the LED-driven microchip gave the best overall results.

From conventional to microphotochemistry: photodecarboxylation reactions involving phthalimides.

A series of acetone-sensitized photodecarboxylation reactions involving phthalimides have been investigated using conventional and microphotochemistry. Both, intra- and intermolecular transformations were compared. In all cases examined, the reactions performed in microreactors were superior in terms of conversions or isolated yields. These findings unambiguously prove the advantage of microphotochemistry over conventional photochemical techniques.

Photosensitized addition of isopropanol to furanones in a 365 nm UV-LED microchip.

The DMBP-sensitized addition of isopropanol to furanones was studied in a novel LED-driven microchip reactor. Complete conversions were achieved after just 2.5 to 5 min of irradiation with 6 × 365 nm high-power LEDs. The results were compared to analogous experiments using a conventional batch reactor.

Analyzing the mechanisms of selectivity in biomimetic self-assemblies via IR and NMR spectroscopy of prepolymerization solutions and molecular dynamics simulations.

Molecularly imprinted polymers (MIPs) for 2,4-dichlorophenoxyacetic acid were synthesized via a noncovalent approach with 4-vinylpyridine as functional monomer and ethylene glycol dimethacrylate as cross-linker in a methanol/water mixture. Templated polymers synthesized in this self-assembly approach rely on complex formation between the target analyte and functional monomers in porogenic solution prior to radical polymerization. Consequently, the achievable selectivity is governed by the nature and stability of these complexes. The nature of noncovalent interactions responsible for complex formation during imprinting of the template 2,4-dichlorophenoxyacetic acid (2,4-D) with the functional monomer 4-vinylpyridine has been investigated. Fourier transform infrared and 1H NMR spectroscopies provide the fundamental analytical basis for rationalizing the mechanisms of recognition during the imprinting process probing the governing interactions for selective binding site formation at a molecular level. Molecular modeling studies in explicit solvent (chloroform and water) corroborate the importance of hydrogen bonding in aprotic solvents and of hydrophobic interactions in protic media in agreement with the experimental spectroscopic investigations of prepolymerization solutions. Furthermore, chromatographic studies of the synthesized MIPs provided insight on the importance of size, shape, and functionality during selective 2,4-D rebinding processes confirming the results obtained during the prepolymerization studies.

Tuning and enhancing enantioselective quenching of calixarene hosts by chiral guest amines.

The synthesis of a propranolol amide derivative of p-allylcalix[4]arene is described, which has been designed to behave as a molecular sensor capable of distinguishing chiral amines on the basis of their shape and chirality. This molecule can discriminate between the enantiomers of phenylalaninol through the quenching of the fluorescence emission in methanol in contrast to an (S)-dinaphthylprolinol calix[4]arene derivative, which can discriminate between the enantiomers of phenylglycinol, but not phenylalaninol. The separation between the naphthyl fluorophores and the hydrogen-bonding sites within the chiral cavity can be tuned to recognize guest amines with similar separation between aryl groups and hydrogen-bonding sites. The formation of metal ion complexes of the p-allylcalix[4]arene propranolol amide derivative is shown to induce a more regular and rigid cone conformation in the calix[4]arene macrocycle, which generates a significant enhancement in the observed enantiomeric discrimination.

Characterisation of the ester-substituted products of the reaction of p-t-butyl calix[4]arene and ethyl bromoacetate using LC-UV-MS and LC-DAD.

A series of derivatisation reactions between p-t-butyl calix[4]arene and ethyl bromoacetate were carried out in order to prepare 1,3 diester substituted calix[4]arene. Mass spectral data, obtained from direct injection of samples, indicated that the reactions were rich in the desired product. Since the ultra violet (UV) spectra of the desired product and possible impurities are very similar, liquid chromatography (LC) chromatographic data seemed to corroborate these results. However, when on-line LC-UV-MS was carried out and each LC peak subjected to MS analysis as it eluted, a very different picture emerged. It was found that many of these reactions actually contained high levels of the monoester product which, having less affinity for sodium in the MS, is therefore seriously underestimated in any direct injection assay. LC-diode array detection (DAD) methods were also used to help successfully identify and characterise the compounds being formed in these complex reactions. The overall results obtained in this paper allowed the optimal reaction conditions to be determined for this reaction. LC-MS analysis of the chromatographic peaks also identified the presence of two isomers of the diester substituted calix[4]arene (1,3 and 1,2 diesters). The combination of LC and UV/MS detection is required for accurate analysis of the products of such reactions.

Synthesis of 2,3,9,10,16,17,23,24-Octaalkynylphthalocyanines and the Effects of Concentration and Temperature on Their (1)H NMR Spectra.

The syntheses of 3,4- and 4,5-diiodophthalonitriles are described. Coupling of the latter compound with Pd(PPh(3))(2)Cl(2) and 1-octyne, 1-heptyne, 1-hexyne, 1-pentyne, and 3,3-dimethyl-1-butyne gave a series of 4,5-dialkynylphthalonitriles. Hydrogenation of 4,5-bis(1-pentynyl)phthalonitrile and 4,5-bis(3,3-dimethyl-1-butynyl)phthalonitrile gave 4,5-dipentylphthalonitrile and 4,5-bis(3,3-dimethylbutyl)phthalonitriles. Condensation of the dialkynylphthalonitriles with lithium 1-pentoxide in 1-pentanol gave 2,3,9,10,16,17,23,24-octaalkynylphthalocyanines, while intervention of the intermediate dilithium phthalocyanines with zinc acetate gave the related zinc(II) phthalocyanines. (1)H NMR spectroscopy of these octaalkynylphthalocyanines exhibited large chemical shifts (1-2 ppm) of the internal and aromatic protons at concentrations ranging from 10(-)(2) to 10(-)(5) M and at temperatures from 27 to 147 degrees C. The effects of aggregation phenomena are discussed. The importance of reporting concentration and temperature values for NMR spectra of phthalocyanines is stressed.